There are many times when we all experience poor cut quality from our Co2 Laser machines. It may be all running well one day and then the next something has changed and you cannot seem to get a good quality cut. If you are not getting a good quality cut on your machine, this short troubleshooting guide may help get your machine performing well again.
Clean the lens at the end of the laser tube, this lens can be contaminated by smoke, dust and fumes, which will reduce the effective cutting power.
Non-Woven Cotton Lens Cleaning Swab – https://s.click.aliexpress.com/e/_AdqQqz
Lens Cleaning Wipes – https://s.click.aliexpress.com/e/_ATEaOz
Lens Cleaning Wipes – 210 Pre-Moistened and Individually Wrapped Lens Cleaning Wipes – https://amzn.to/2RQlhkh
Isopropyl Alcohol – https://amzn.to/32Bzwf1
Check the mirrors well aligned and clean. You may have performed a mirror alignment in the past and had everything spot on. Make sure the adjustment knobs are secure, if the locking nut is loose then vibrations and movements may result in the mirrors slowly going out of alignment. This de-alignment of the mirror may not be noticeable right away, but as they continue to move it will drastically decrease the quality and ability to cut effectively.
Dirty mirrors will not effectively reflect the laser beam light and this results in reduced power at the material being cut.
Co2 Laser Mirrors – https://s.click.aliexpress.com/e/_ArWXYz
When aligning mirrors, don’t forget to make sure the final alignment of the lens through the laser nozzle is coming out centered.
Check the nozzle for contamination. Remove the laser lens nozzle, and clean it. Dirt and splatter from materials being cut can start to clog the nozzle. As a result the laser beam will need to burn away this material, causing a reduction in power before the beam hits the material being cut, reducing the efficient power at the material.
Check the air assist. To reduce fouling of the laser focusing lens and build up of contaminants ensure you have a positive air pressure at the nozzle at all times while cutting and engraving materials, and clean the nozzle regularly.
Ultimate Air Assist Kit – https://s.click.aliexpress.com/e/_Adrayp
If using high pressure air for cutting check the pressure used is the same as you have previously used and tested on your material.
If a water trap is installed on the air line drain it regularly to prevent condensation on the focusing lens.
Oil & Water Separator Trap Regulator – https://s.click.aliexpress.com/e/_9u7sVF
California Air Tools 8010 Air Compressor Ultra Quiet – https://amzn.to/3n8hVox
Check the laser focusing lens is clean and correctly inserted, carefully remove the lens and clean with a lint free cloth. If possible do not handle the lens, use a holder or soft cloth.
Co2 Laser Focus Lens CVD ZnSe – https://s.click.aliexpress.com/e/_AmEvvr
Co2 Laser Lenses – https://amzn.to/3vbqqC4
While cleaning the lens check to make sure it is not cracked or scratched. Check the correct focal length lens has been installed, and it is installed correctly.
Check your focus gap. This is more overlooked with machines that use an autofocus system, where users take for granted that the calibration and autofocus system remains accurate.
Co2 Laser Lens Selection & Ramp Test – https://youtube.com/watch?v=gGfg2zJioT8
Auto Focus Sensor – https://s.click.aliexpress.com/e/_99J349
Check that the laser bed is level, and make adjustments where required. A simple way to check this is using an engineers square, with one edge on the laser bed and then measure to the underside of the X Axis Rail in all areas of the worktable.
Engineer/Carpenter Square – https://s.click.aliexpress.com/e/_AdU0aN
Cutting speed and power settings. Compare the laser cutting and speed settings with those that you have previously known to achieve good cuts quality with.
If you have a milliamp (mA) meter installed, A good tip is to record mA from your laser tube and the power % for a known cut and monitor this over time.
Ammeter Analog – https://s.click.aliexpress.com/e/_AppDk5
Ammeter Digital – https://s.click.aliexpress.com/e/_AMwJ9B
The lifespan of a standard Glass Co2 Laser tube is around 10,000 hours. So for a machine operating for 4 hours a day, this is 10,000 hrs / 4 hrs = 2,500 days or approximately 7 years. However the gases can permeate the glass even while the laser is not in use, so normally 3 years is the expected lifespan of a Glass Co2 Laser Tube if it is used in good conditions.
HM Laser – Glass Co2 Laser Tubes – https://en.hmlaser.com/
NOTE: This is not a paid production or advertisement.
Show your support for MW Laser by Buying Matt a Coffee.
This can be done via our website https://buymeacoffee.com/mwlaser
Until next time, take care
Cheers Matthew
Visit MW Laser https://mwlaser.com.au
Facebook https://facebook.com/groups/mwlaser
Email: askmattmwlaser.com.au
UCYmaUPBZ6oF_OExb3htzTOw
co2 laser
#Co2 #Laser #Troubleshooting #Guide #Troubleshooting #Poor #Cut #Quality